RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Walo
Showing results 1 to 15 of 15
Search took 0.02 seconds.
Forum: RC Jets
08-16-2015, 01:51 AM
Replies: 3,501
Views: 601,488
Posted By Walo

This can occur when the SD Card is faulty or...

This can occur when the SD Card is faulty or full. Important: A Screenshot with a full SD card in flight could cause a freeze. I'm not shure if it's a total failure or not but I definitly don't do...
Forum: RC Jets
07-21-2015, 11:19 PM
Replies: 3,501
Views: 601,488
Posted By Walo

Hello Jeti USA, You wrote this allready a...

Hello Jeti USA,

You wrote this allready a year ago. According to Jeti Czech there is no update in the near future. Where did you get this info?

Regards
Walter
Forum: RC Jets
07-02-2015, 03:58 AM
Replies: 3,501
Views: 601,488
Posted By Walo

Were all your devices (Servo, Gear...) approved...

Were all your devices (Servo, Gear...) approved for HV (High Voltage)? I know that some servos do not like A123, even if they are rated for 6,0 Volts.

Regards, Walter
Forum: RC Jets
04-06-2015, 01:11 AM
Replies: 3,501
Views: 601,488
Posted By Walo

I use the built in failsafe function of the...

I use the built in failsafe function of the Jetcat ECU. The throttle channel of my Receiver is set to "Out/Off". The ECU will go into failsafe mode either with a Receiver or a Transmitter failure....
Forum: RC Jets
11-27-2014, 08:25 AM
Replies: 3,501
Views: 601,488
Posted By Walo

It's probably not that simple :rolleyes:. I...

It's probably not that simple :rolleyes:.

I just got mine and realized that it comes with an additional Temperature Sensor (up to 85°C). Could be used to check critical compartement aereas.
It's...
Forum: RC Jets
07-15-2014, 12:25 AM
Replies: 3,501
Views: 601,488
Posted By Walo

...then try flying indoor with autotrim :o ...

...then try flying indoor with autotrim :o

No, the trim Buttons are definitively a negative point, also the timers. You have a bunch of useless timers built in and not one of it is variable.
...
Forum: RC Jets
04-12-2014, 02:05 PM
Replies: 3,501
Views: 601,488
Posted By Walo

Ok, I will switch Failsave off. Good to know! ...

Ok, I will switch Failsave off. Good to know!

Right now for the programming I have two sattellites and one R3 Switch connected to the CB200. But I've not yet decided if I want to fly in this...
Forum: RC Jets
04-06-2014, 11:28 AM
Replies: 3,501
Views: 601,488
Posted By Walo

Ok, that worked. But I guess this is true for an...

Ok, that worked. But I guess this is true for an RSAT as Satellite. When I use an R3 and need one Servo Output directly from the R3 I will have to switch Failsave on and set 17ms.
I'm programming a...
Forum: RC Jets
04-04-2014, 11:29 AM
Replies: 3,501
Views: 601,488
Posted By Walo

Thanks, that works! Walter

Thanks, that works!

Walter
Forum: RC Jets
04-03-2014, 01:56 AM
Replies: 3,501
Views: 601,488
Posted By Walo

I had Problems with "Auto" when I connected two...

I had Problems with "Auto" when I connected two SAT Receivers to the Central Box 200. Analog Servos didn't like it. Increasing latency to 20ms before switching to EX Mode solved the Problem. These...
Forum: RC Jets
02-09-2014, 09:18 AM
Replies: 3,501
Views: 601,488
Posted By Walo

I do not use flight mode trim but a free mix...

I do not use flight mode trim but a free mix Flaps to Flaps, Master Value 100%, Separate, Constant Curve. With the Constant curve you can set your flaps for each flight condition separate.
My tip: I...
Forum: RC Jets
01-27-2014, 06:46 AM
Replies: 3,501
Views: 601,488
Posted By Walo

We discussed it in the european Jeti forum....

We discussed it in the european Jeti forum. Implementation for the EX bus protocol is planned but not yet realized.

Regards, Walter
Forum: RC Jets
01-25-2014, 11:14 PM
Replies: 3,501
Views: 601,488
Posted By Walo

I guess you never tried it. I did more then fifty...

I guess you never tried it. I did more then fifty flight and it works perfect. And you can use it for electric planes too. A good ECU monitor device would be great but there is none for JetCat...
Forum: RC Jets
01-25-2014, 04:18 PM
Replies: 3,501
Views: 601,488
Posted By Walo

We will do it without this stuff once we get a...

We will do it without this stuff once we get a "variable timer" like the 300$ Transmitter Taranis has.

Walter
Forum: RC Jets
01-21-2014, 09:03 AM
Replies: 3,501
Views: 601,488
Posted By Walo

You might have to increase "Throttle-Idle Offset"...

You might have to increase "Throttle-Idle Offset" to 30% in order to get enough spread between Throttle Cut and Idle. My servomonitor shows now -130% for Throttle Cut, +30% for Idle and +100% for...
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.