RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: DAMBUSTER
Showing results 1 to 11 of 11
Search took 0.03 seconds.
Forum: RC Jets
03-30-2016, 01:39 PM
Replies: 3,501
Views: 601,539
Posted By DAMBUSTER

O.K. guys,have to come clean..... there was no...

O.K. guys,have to come clean..... there was no problem with the iGyro 3e or Jeti the problem was......ME. As suggested I had the connections,in and out, the wrong sides. Thanks to a good mate all is...
Forum: RC Jets
03-26-2016, 01:33 PM
Replies: 3,501
Views: 601,539
Posted By DAMBUSTER

Sorry ...P.S. Yes model works correctly on all...

Sorry ...P.S. Yes model works correctly on all servos with either Rx when the 3e is not in circuit.
Dambuster.
Forum: RC Jets
03-26-2016, 01:32 PM
Replies: 3,501
Views: 601,539
Posted By DAMBUSTER

Hi Guys, Thank you for your answers, I have...

Hi Guys,
Thank you for your answers, I have absolutely made sure the plugs are correctly orientated, I have now tried a REX 12 rx in the model and it STILL doesn't work,I have tried another 3e that...
Forum: RC Jets
03-25-2016, 01:00 AM
Replies: 3,501
Views: 601,539
Posted By DAMBUSTER

Hi, I have a DS 16 updated to 4.0,also an R14us...

Hi, I have a DS 16 updated to 4.0,also an R14us rx updated to 3.24. I have an iGyro 3e , but I can't get any control response at all when the Gyro is in the system even if the gain is zero. When I...
Forum: RC Jets
08-25-2014, 01:00 AM
Replies: 3,501
Views: 601,539
Posted By DAMBUSTER

Hi, In addition to Pepperpetes query I have used...

Hi, In addition to Pepperpetes query I have used a three position switch (SA) to flight modes for take off and landing,I have also set up crow for landing and slowed the servo response. The problem...
Forum: RC Jets
08-13-2014, 07:36 PM
Replies: 3,501
Views: 601,539
Posted By DAMBUSTER

Hi LA jetguy, Again thank you for your help,it is...

Hi LA jetguy, Again thank you for your help,it is much appreciated.I will go and "play" !
Cheers Dambuster.
Forum: RC Jets
08-12-2014, 10:47 PM
Replies: 3,501
Views: 601,539
Posted By DAMBUSTER

Hi, LA jetguy,please accept my apology for being...

Hi, LA jetguy,please accept my apology for being so tardy in getting back,but thank you for your help with the steering programming. It works perfectly.I hope I didn't seem too rude.
I have another...
Forum: RC Jets
07-30-2014, 07:58 PM
Replies: 3,501
Views: 601,539
Posted By DAMBUSTER

Hi All, I own a DS-16,I want to inhibit the...

Hi All, I own a DS-16,I want to inhibit the steering servo when the 'cart is retracted. I have tried via the sequencer where I have (I think!) the doors and 'cart sequenced to:- doors open,'cart...
Forum: RC Jets
07-15-2014, 11:02 PM
Replies: 3,501
Views: 601,539
Posted By DAMBUSTER

Forget using "differential",adjust "servo travel"...

Forget using "differential",adjust "servo travel" so that the down going aileron moves less than the up going,just make sure both ailerons travel the same amount,up and down. Also in the same screen...
Forum: RC Jets
06-30-2014, 01:06 AM
Replies: 3,501
Views: 601,539
Posted By DAMBUSTER

Hi Goose,Thank you for your prompt reply,I will...

Hi Goose,Thank you for your prompt reply,I will programme as you say.
The Jeti radio is worth buying for the support available alone ! Wish I could say the same for my other top end radio. Perhaps...
Forum: RC Jets
06-29-2014, 03:06 PM
Replies: 3,501
Views: 601,539
Posted By DAMBUSTER

Hi,I have recently bought a DS-16,I have received...

Hi,I have recently bought a DS-16,I have received great support from Esprit and,in particular,from Peter Vogel (thank you Peter !).The question I now have is that I have set up flap on a three...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.