RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Community
Search
Notices
Search: Posts Made By: merlin6161
Showing results 1 to 11 of 11
Search took 0.02 seconds.
Forum: RC Jets
08-11-2016, 12:29 AM
Replies: 3,501
Views: 601,550
Posted By merlin6161

Hi, Does anyone know if it is possible to...

Hi,

Does anyone know if it is possible to use a Jeti TF module in a Futaba 9C as a buddy box wirelessly connected to a ds16 in wireless trainer mode? If so what are the steps to pair the two...
Forum: RC Jets
07-16-2016, 04:46 AM
Replies: 3,501
Views: 601,550
Posted By merlin6161

I will be using 8411s. It's all a bit confusing...

I will be using 8411s. It's all a bit confusing as many people use these on 6v no problem. JR, I believe, say it's ok but Horizon don't. Jet guru's in the UK say don't use any JR servos at 6v . In...
Forum: RC Jets
07-15-2016, 04:07 AM
Replies: 3,501
Views: 601,550
Posted By merlin6161

Wayne, I appreciate your reply, thank you. I...

Wayne, I appreciate your reply, thank you. I agree I think the CB200 may be a little over the top for what I want and I'll stick with the R14/Rsat set up. Using A123s with the CB would have been a...
Forum: RC Jets
07-14-2016, 06:36 AM
Replies: 3,501
Views: 601,550
Posted By merlin6161

Hi All, I have an Elan set up with an...

Hi All,

I have an Elan set up with an R14/Rsat powered by two Jeti batteries through a PB sensor switch. This set up has worked well and I was going to use the same set up for my new Ultraflash...
Forum: RC Jets
09-30-2014, 01:14 AM
Replies: 3,501
Views: 601,550
Posted By merlin6161

I have a question for the Cortex experts. ...

I have a question for the Cortex experts.

When learning to fly jets I was told to apply and hold up elevator at the start of the takeoff run, so when the jet reached a speed that the elevator...
Forum: RC Jets
08-22-2014, 01:55 PM
Replies: 3,501
Views: 601,550
Posted By merlin6161

Hi all, My DS-16 is now back from Jeti after...

Hi all,

My DS-16 is now back from Jeti after the problems I had a few months ago. Jeti have not indicated whether they found anything wrong or not. All I know is that the Tx firmware has been...
Forum: RC Jets
06-18-2014, 12:17 AM
Replies: 3,501
Views: 601,550
Posted By merlin6161

Goose, I'm going to take your advice and send...

Goose,
I'm going to take your advice and send all my gear back to Jeti. I was hoping that they were going to get back me with some advice but I sent them all the info I could at the beginning of May...
Forum: RC Jets
06-17-2014, 07:40 AM
Replies: 3,501
Views: 601,550
Posted By merlin6161

Goose, We don't appear to have a Jeti...

Goose,

We don't appear to have a Jeti service centre here in the UK, only a distributor. I have contacted them and they say "do what Jeti suggest" only Jeti have not yet responded even though it...
Forum: RC Jets
06-17-2014, 02:31 AM
Replies: 3,501
Views: 601,550
Posted By merlin6161

Hi Mort, Thanks for your reply. It is...

Hi Mort,

Thanks for your reply.

It is interesting that you said your model was acting weird before the crash. I too noticed strange behaviour before the signal loss when I was setting up the...
Forum: RC Jets
06-17-2014, 01:20 AM
Replies: 3,501
Views: 601,550
Posted By merlin6161

Goose, thanks for the reply. The Rx...

Goose, thanks for the reply.

The Rx definitely didn't go to failsafe. It was programmed for the throttle to go to idle and everything else to centre. This was tested the same day on the ground and...
Forum: RC Jets
06-16-2014, 12:38 PM
Replies: 3,501
Views: 601,550
Posted By merlin6161

Hello Everyone, I have been following this...

Hello Everyone,

I have been following this thread since I discovered it a couple of weeks ago and have now caught up. I have learned loads and would like to thank the chaps who give so much time...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.