RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Gaspar
Showing results 1 to 11 of 11
Search took 0.02 seconds.
Forum: RC Jets
03-30-2016, 10:57 PM
Replies: 3,501
Views: 601,547
Posted By Gaspar

Just an small tip for those use the Xicoy...

Just an small tip for those use the Xicoy telemetry adapter and taxi tank, having the need to reset the fuel counter while the engine run. Just install an small switch between the ecu and the...
Forum: RC Jets
02-22-2016, 09:59 AM
Replies: 3,501
Views: 601,547
Posted By Gaspar

I have not tested it myself, but is my...

I have not tested it myself, but is my understanding that in this case you should set the ProfiBox in "monitor mode" and link it to the Transmitter, not to one of the receivers. In this way you have...
Forum: RC Jets
02-19-2016, 04:39 AM
Replies: 3,501
Views: 601,547
Posted By Gaspar

Yes, but not all telemetry adapters have this...

Yes, but not all telemetry adapters have this function. Was added at same time as the compatibility with Graupner Hott radios in November 2014. Label should say "Telemetry-2".

On these, on the...
Forum: RC Jets
02-19-2016, 01:39 AM
Replies: 3,501
Views: 601,547
Posted By Gaspar

Just a small comment when using our telemetry...

Just a small comment when using our telemetry adapter, if the alarm is defined on the adapter itself (not in the TX), the alarm is inhibited until the remaining of fuel is below the 98%, to not...
Forum: RC Jets
05-22-2015, 06:57 AM
Replies: 3,501
Views: 601,547
Posted By Gaspar

Hi Harry, Is one of our valves? Ours have a...

Hi Harry,

Is one of our valves? Ours have a power-up delay of 3 seconds, in theory should be in aft for the RX to boot and supply a stable signal, but I can increment a bit more this time if...
Forum: RC Jets
05-29-2014, 02:41 AM
Replies: 3,501
Views: 601,547
Posted By Gaspar

Could be a resettable PolyFuse, long ago since I...

Could be a resettable PolyFuse, long ago since I checked, but in this case I don't expect more than 4A per output.

Gaspar
Forum: RC Jets
05-28-2014, 10:54 PM
Replies: 3,501
Views: 601,547
Posted By Gaspar

Outputs of the CB200 are protected by individual...

Outputs of the CB200 are protected by individual fuses, once blown, you need to replace them.

Gaspar
Forum: RC Jets
01-29-2014, 11:52 PM
Replies: 3,501
Views: 601,547
Posted By Gaspar

Hi Jim, I'm sorry, but in your assumption of...

Hi Jim,

I'm sorry, but in your assumption of how our fadec ecu works you have assumed some facts that are not true and overcomplicated the setup.

First, the ecu don't expect a preset value of...
Forum: RC Jets
12-01-2013, 07:56 AM
Replies: 3,501
Views: 601,547
Posted By Gaspar

I'm not a JETI expert, but our adapter is seen by...

I'm not a JETI expert, but our adapter is seen by the system as any other sensor, so it should be the same as all other sensors. Don't have a PowerBox to test, but the Jeti satellite receiver I have...
Forum: RC Jets
12-01-2013, 01:54 AM
Replies: 3,501
Views: 601,547
Posted By Gaspar

Hello MK, Currently it is entered...

Hello MK,



Currently it is entered using the data terminal of the engine. In a future release, trough JetiBox.


No, just our fadec-jeti adapter
Forum: RC Jets
11-24-2013, 02:00 PM
Replies: 3,501
Views: 601,547
Posted By Gaspar

Hi, Just a little comment to announce that we...

Hi,
Just a little comment to announce that we have finished the development of the adapter for Xicoy FADECs to the Jeti telemetry system. Below some (bad) photos of the TX screen where you can see...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.